ANALYSIS OF CONSTRUCTIVE FACTORS AFFECTING THE FATIGUE STRENGTH OF METALLURGICAL EQUIPMENT PARTS
DOI:
https://doi.org/10.34185/1562-9945-2-145-2023-03Keywords:
fatigue failure, stress concentrators, endurance limitAbstract
The causes of fatigue failure of metallurgical equipment parts were analyzed. The correlation between the effect of the quality of surface treatment of the part on the fatigue strength has been established. The influence of local stress concentrators on fatigue strength has been determined. Recommendations for increasing the fatigue strength of the finished part were given
References
Influence of technological process parameters on equipment dynamic factor / O. Hrechanyi et al. System technologies. 2021. Vol. 3, no. 134. P. 3–12.
URL: https://doi.org/10.34185/1562-9945-3-134-2021-01
Hrechanyi O. M. Substantiation of the choice of technical parameters of the guillotine shears of the rolling mill. Metallurgy: scientific works of the Zaporizhia State Engineering Academy. 2017. Vol. 38, no. 2. P. 126–130.
Application of risk-analysis methods in the maintenance of industrial equipment / S. V. Belodedenko et al. Procedia Structural Integrity. 2019. Vol. 22. P. 51–58. URL: https://doi.org/10.1016/j.prostr.2020.01.007
Nalobina O. O. Construction of nodes and aggregates: Method. instructions (lec-ture notes). Rivne: NUVHP, 2019. 83 с.
Vasilchenko T.O., Shevchenko I.A., Hrechanyi O.M. Resistance of materials: edu-cational and methodological manual Zaporizhzhia: ZNU, 2020. – 263 p.
ISO 1143:2021. Metallic materials – Rotating bar bending fatigue testing. – Re-places ISO 1143:2010 ; effective from 2021-07-01. – Official edition. – [S. l. : s. n.], 2021. – 26 p.
Endurance under a complex stress state in the aspect of prolonging the resource of technological equipment of industrial production / S. V. Bilodidenko et al. Theory and practice of metallurgy. 2021. № 4. С. 56–68.
URL: https://doi.org/10.34185/tpm.4.2021.07
Belodedenko S., Grechany A., Yatsuba A. Prediction of operability of the plate rolling rolls based on the mixed fracture mechanism. Eastern-European Journal of Enterprise Technologies. 2018. Vol. 1, no. 7 (91). P. 4–11.
URL: https://doi.org/10.15587/1729-4061.2018.122818
Dyachenko S.S. Materials of various purposes, their processing and properties: educational guide / S.S. Dyachenko, I.V. Doshchechkina, I.V. Ponomarenko, S.I. Bondarenko, Kh.: Khnadu, 2016. ‒ 348с.
Acceleration of Saturation Process and Improving Nitrided Layer Properties / S. Dyachenko et al. Indstrial Heating. 1998. No. 65. P. 99–105.
Afanasieva O.V. Materials science and construction materials. Education manu-al. - Kharkiv: KhNURE, 2016. – 188 с.
Dzyura V. O., Marushchak P. O. Technological methods of ensuring quality pa-rameters of surfaces of rotating bodies and their profilometric control: monograph. Ternopil: FOP Palyanytsia V. A., 2021. – 170 p.
Dyck T., Ober-Wörder P., Bund A. Calculation of the wear surface and the coeffi-cient of friction for various coated contact geometries. Wear. 2016. Vol. 368-369. P. 390–399. URL: https://doi.org/10.1016/j.wear.2016.10.014
Degtyarev V. A. Influence of the ratio of dynamic and static stresses on brittle fracture resistance of low-alloyed steel welded joints. Automatic welding. 2017. Vol. 2017, no. 9. P. 3–9. URL: https://doi.org/10.15407/as2017.09.01
Influence of stress concentration on steel deformation 20 under cyclic loads / M. Gladskyi et al. Technical sciences and technologies. 2022. No. 1(27). P. 60–66. URL: https://doi.org/10.25140/2411-5363-2022-1(27)-60-66
